每年高温灭菌季，做医用透析器、灭菌盘的厂就要开始提心吊胆。
去年有个客户，一批透析器外壳用了来路不明的“TPX料”，环氧乙烷灭菌一过，壳体直接瘪下去一圈，透明罩子雾得像磨砂玻璃。整批货退回来，十几万一吨的料赔进去不说，客户验厂记录还留了个黑点。
说白了，PMP这东西，贵是真贵，偏是真偏，但一旦用错位置，翻车翻得比谁都干脆。今天就把这门小众生意讲透。
一、PMP是什么，全球盘子小到什么程度
PMP的学名很长——聚4-甲基戊烯-1，商品名几乎只有一个：TPX。
它是目前工业化聚烯烃里密度最低的那一档，0.83g/cm³上下，比水还轻；熔点却能扛到220℃以上，透明、耐化学、还能透过微波。轻得像羽毛，耐热却能进灭菌锅，这俩属性凑一块，就是它独有的位置。
全球格局说出来你可能不信：PMP这个品类，几乎是三井化学一家撑起来的。三井化学自己的产品页写得很直白——TPX是全世界独一份的制造、销售体系。多家市场研究机构交叉看下来，三井化学在全球PMP树脂产能里占了七成以上，商业牌号超过15个，RT、DX、MX系列分得清清楚楚，年产能在两万吨量级。
真正能做PMP原树脂的国外玩家屈指可数：三井化学是绝对主力；住友化学在其高分子事业部也有少量PMP树脂供应；再往下，Ensinger、RTP Company、Westlake Plastics这些名字，其实是拿三井的TPX原树脂去做改性和板材加工的，并不生产原树脂。
所以这个品类不存在“全球前三随便挑”——它是个寡头到接近独一份的盘子。买PMP副牌，本质上就是在买三井TPX体系里那批指标小幅浮动的原厂料。
二、PMP副牌到底是个什么来头
▍TPX副牌密度卡在0.83g/cm³、熔点在220℃上下浮动几度，它和正牌出自同一套配位聚合装置——只是透光率或耐热那一栏化验时差了零点几个百分点。
先把定义说死：副牌，是同一厂家、同一牌号的产品里，出厂检验没完全达到正牌技术指标的那一部分。同一批聚合产物，检验全过贴正牌标签，个别指标差一点点，就是副牌。
PMP副牌的四大来源，和其他聚烯烃一个逻辑：装置开停车时的头尾料、牌号切换时的过渡料、工艺波动导致熔指或色相小幅超标的批次、副线尾料。
关键在于——它仍然是原厂原生聚合粒子，分子结构和正牌一模一样，只是个别指标小幅浮动。不是废旧料再造粒，不是水口料回炉。
这里要把边界划清楚：
| 类型 | 来源 | 品质 | 典型用途 |
|---|
| 正牌 | 原厂达标批次 | 全指标达标、批次稳 | 高光透明外罩、认证医疗件 |
| 副牌 | 原厂未达标批次 | 个别指标小幅偏离，基材一致 | 医疗内件、配色件、一般耐热件 |
| 回料/水口料 | 加工边角料再造粒 | 已吃过一次热历史 | 低要求制品 |
| 再生料 | 废旧塑料回收造粒 | 性能波动大 | 低端填充 |
PMP这料本身就贵，拿再生料冒充副牌去做医疗件，是要出事的事。
三、三井化学：TPX这个商标就是它注册的
头一家，也是绕不开的一家——三井化学。
TPX这个商标就是三井注册的，RT18、MX002、MX004这些牌号，做光学离型膜、医疗耗材、食品化妆品包装的人都熟。三井从单体4-甲基戊烯-1到聚合垂直打通，别人想仿都难。
它的副牌主要出在两个指标上：一是透光率或雾度，二是色相、黄度指数。说白了，就是透明件做不了高光外罩，但做透析器壳体、灭菌盘、实验器皿、食品托盘，完全够用。
三井TPX的副牌流通上，大包装小包装都有，原厂原包出来，批号可追。做医疗内件、一般耐热透明件的厂，拿精选副牌替代正牌，成本能下来一截，性能又不跑偏。
四、住友化学：不声不响的第二梯队
第二家要单独拎出来讲——住友化学。
很多人不知道住友也做PMP。它的高分子事业部面向电子和医疗包装供应高纯PMP树脂，量不大，但走的是高纯度路线，给对金属离子、析出物敏感的电子和医疗场景供货。
这个梯队要诚实说清楚：除了三井，全球能稳定供PMP原树脂的国外厂商非常少。住友算一个，剩下的更多是区域级的改性和板材加工厂。所以买PMP副牌，别听人忽悠“我们家也有进口PMP原厂料”——先问一句：你是哪家原树脂厂出的？答不上来的，多半是改性料或者进口副牌二次分装。
五、改性加工梯队：塔顶之外的活儿
第三层，是改性与板材加工梯队。
Ensinger、RTP Company、Westlake Plastics这几家，本身不做PMP聚合，但它们从三井拿TPX原树脂，做玻纤增强、矿物填充、色母改性，做成板材、棒材、精密加工件。Honeywell在美国市场也做TPX的分销。
这一层的“副牌”概念要换个理解：不是原树脂副牌，而是改性过程中指标小幅波动的批。对于做实验器皿、微波餐具、耐热托盘的下游，这一层的料性价比很高，但要认准是哪家改的、用的哪家原树脂。
说白了，PMP的产业链就是这样：三井在塔顶，住友在塔腰，改性厂在塔底做应用。买副牌，先想清楚你买的是哪一层。
六、买PMP副牌，四个坑先标出来
讲完格局，说几个真会踩的坑。
第一，别把“TPX副牌”和“透明PP”混为一谈。PP透明料虽然也透，但扛不住220℃的灭菌温度，一进环氧乙烷灭菌锅就软。
第二，看析出物和离子含量。做医疗、电子的，副牌也要看析出物指标，不是便宜就上。
第三，批次留样。PMP批次间哪怕熔指差一点点，做薄壁透析器壳体的壁厚就可能飘。进厂先留样、先试模，量产再上量。
第四，认批号。三井TPX的原厂副牌批号可追溯，分装换包的要打个问号。
记住一句话：PMP副牌省的是钱，赌不起的是灭菌锅那一轮。
科隆仓库现货｜PMP老客
主推品牌：三井化学、住友化学、改性加工梯队（Ensinger/RTP/Westlake）。
主要牌号：TPX（RT18/MX002/MX004）、住友高纯PMP、TPX玻纤增强/矿物填充改性料。
包装规格：小包副牌与箱装副牌走小包装，大包料/吨包料走吨袋，按车间用量分包装备货。
仓库现货：PMP仓库现货通常在5000吨左右，其中小包副牌备货800-1000吨、箱装副牌备货300-500吨、大包料/吨包料备货3500-3900吨。
供应保障：先测后签，小样过了再走大货。
七、选型口诀和一个丽水的案子
给你几句选型口诀：
一看用途——高光透明外罩走正牌，内件托盘再考虑副牌；
二看指标——析出物、离子、透光率，医疗电子件一项都不能放；
三看批号——原厂原包、批号可追，分装的先打问号；
四看试模——先小样试模、再批量上机，壁厚稳住再走量。
说个真事。丽水有家做医用透析器和灭菌盘的客户，之前图便宜拿了批来路不清的“TPX料”，灭菌后壳体变形率跑到8%，整批退货损失二十多万。后来换成三井TPX体系的原厂副牌，析出物和壁厚指标对上后，灭菌后变形率压到0.3%以内，良率从七成拉到九成五。
这就是选型的价值——PMP这东西，用对了是省钱，用错了是烧钱。宁波市科隆新材料有限公司做进口聚烯烃副牌这些年，类似的案子每年都接，说白了就是帮你在量产前把灭菌锅那一关先趟平。
资料与数据来源
1. 三井化学台湾官网 TPX（Polymethyl Pentene）产品页，mitsuichemicals.com，核验日期2026-09-14。
2. PW Consulting《Worldwide Polymethylpentene (PMP) Market 2026》，pmarketresearch.com，核验日期2026-09-14。
3. Dataintelo《Poly 4 Methyl 1 Pentene Sales Market》，dataintelo.com，核验日期2026-09-14。
4. 24ChemicalResearch《Polymethylpentene PMP Market Outlook and Forecast 2026-2033》，24chemicalresearch.com，核验日期2026-09-14。
Every year during the high-temperature sterilization season, factories that make medical dialyzers and sterilization trays have to start being on edge.
Last year, there was a client whose batch of dialyzer housings was made with some unknown 'TPX material.' Once they underwent ethylene oxide sterilization, the housings dented all around, and the transparent covers became frosted like sandblasted glass. The entire batch was returned, not to mention losing material worth hundreds of thousands per ton, and the client's factory inspection record also left a black mark.
Frankly speaking, PMP is really expensive and definitely niche, but once used in the wrong place, it can backfire more abruptly than anything else. Today, let's thoroughly explain this niche business.
1. What is PMP, and how small is its global market?
The scientific name of PMP is very long—poly(4-methylpentene-1), and it basically has only one trade name: TPX.
It is currently the lowest density grade among industrialized polyolefins, around 0.83 g/cm³, lighter than water; yet its melting point can withstand over 220℃, it is transparent, chemically resistant, and can allow microwaves to pass through. As light as a feather, heat-resistant enough to go into a sterilization autoclave, these two properties together give it its unique position.
You might not believe it when the global situation is explained: for the PMP category, it is almost solely supported by Mitsui Chemicals. Mitsui Chemicals’ own product page states very plainly that TPX has a unique manufacturing and sales system in the world. Cross-referencing multiple market research institutions shows that Mitsui Chemicals accounts for over 70% of global PMP resin capacity, with more than 15 commercial grades, clearly divided into the RT, DX, and MX series, with an annual capacity at the 20,000-ton level.
There are very few foreign players who can truly produce original PMP resin: Mitsui Chemicals is the absolute main force; Sumitomo Chemical also supplies a small amount of PMP resin through its polymer division; beyond that, names like Ensinger, RTP Company, and Westlake Plastics actually use Mitsui's TPX original resin for modification and sheet processing, and do not produce the original resin themselves.
So this category does not have 'just pick any top three globally'—it's a market dominated by a few giants, almost to the point of being a monopoly. Buying a PMP sub-brand is essentially buying raw materials from the original factory within the Mitsui TPX system, where the specifications fluctuate only slightly.
2. What exactly is the story behind the PMP sub-brand?
▍The TPX sub-brand has a density of 0.83 g/cm³ and a melting point that fluctuates a few degrees around 220℃. It comes from the same set of coordination polymerization equipment as the main brand—it's just that when tested, the transparency or heat resistance column differed by a few tenths of a percent.
Let's first clearly define it: a secondary brand refers to the portion of products from the same manufacturer and the same grade that did not fully meet the technical specifications of the primary brand during factory inspection. For the same batch of polymer products, if all inspections pass and are labeled as the primary brand, but a few indicators are slightly off, that is a secondary brand.
The four main sources of PMP by-products follow the same logic as other polyolefins: the head and tail materials during plant start-up and shutdown, the transition materials when switching grades, batches that slightly exceed viscosity or color limits due to process fluctuations, and the tailings from the secondary line.
The key is — it is still original factory native aggregated particles, with a molecular structure exactly the same as the genuine product, only some individual indicators fluctuate slightly. It is not recycled scrap material or sprue material reprocessed.
Here we need to clearly define the boundaries:
| Type | Source | Quality | Typical uses |
|---|
| Authentic brand | Original factory standard batch | All indicators meet the standards, batch stability | Glossy transparent outer shell, certified medical parts |
| Side dish | Original factory substandard batch | Individual indicators slightly deviate, substrate is consistent | Medical internal parts, color-matching parts, general heat-resistant parts |
| Recycled material / Sprue material | Processing scrap material into regranulate | Have eaten hot history once | low-specification product |
| Recycled material | Recycled Plastic Pelletizing | Performance fluctuates greatly | low-end filler |
PMP material itself is expensive, using recycled material to pass off as a secondary brand for making medical parts is asking for trouble.
3. Mitsui Chemicals: The trademark TPX is registered by them
The first company, and an unavoidable one—Mitsui Chemicals.
The TPX trademark is registered by Mitsui. The grades RT18, MX002, and MX004 are familiar to people who work with optical release films, medical consumables, and food and cosmetic packaging. Mitsui has a vertical integration from the monomer 4-methylpentene-1 to polymerization, making it difficult for others to imitate.
Its sub-brands mainly focus on two indicators: one is light transmittance or haze, and the other is hue and yellowness index. Simply put, it can't be used for high-gloss covers for transparent parts, but it's completely sufficient for making dialysis device housings, sterilization trays, laboratory equipment, and food trays.
For the circulation of Mitsui TPX's sub-brand, there are both large and small packages. They come in original packaging from the factory, and the batch numbers can be traced. Manufacturers of medical inner parts and general heat-resistant transparent parts use selected sub-brand products to replace the main brand, which can reduce costs significantly without compromising performance.
4. Sumitomo Chemical: The Quiet Second Tier
The second one needs to be discussed separately — Sumitomo Chemical.
Many people do not know that Sumitomo also produces PMP. Its polymer division supplies high-purity PMP resin for electronic and medical packaging. The quantity is not large, but it follows a high-purity approach, supplying electronic and medical applications that are sensitive to metal ions and precipitates.
This tier needs to be honest and clear: apart from Mitsui, there are very few foreign manufacturers worldwide that can reliably supply PMP virgin resin. Sumitomo counts as one, and the rest are mostly regional-level modified and sheet processing plants. So when buying PMP secondary brands, don’t be fooled by people saying 'we also have imported PMP from the original factory'—first ask: which original resin manufacturer produced it? If they can’t answer, it’s most likely modified resin or repackaged imported secondary brand.
5. Modified Processing Team: Work Beyond the Top of the Tower
The third level is the echelon of modification and sheet processing.
Companies like Ensinger, RTP Company, and Westlake Plastics do not produce PMP polymers themselves, but they obtain TPX raw resin from Mitsui and process it into glass fiber reinforced, mineral filled, and color masterbatch modified materials, producing sheets, rods, and precision machined parts. Honeywell also distributes TPX in the U.S. market.
The concept of 'secondary resin' at this level should be understood differently: it is not the original resin secondary product, but batches with slight fluctuations in indicators during the modification process. For downstream applications such as laboratory glassware, microwave tableware, and heat-resistant trays, this level of material offers a high cost-performance ratio, but it is important to know which company performed the modification and which company's original resin was used.
To put it bluntly, the PMP industry chain is like this: Mitsui is at the top of the tower, Sumitomo is in the middle, and the modifiers are at the bottom doing applications. When buying a secondary brand, first think clearly about which layer you are buying.
6. Buying a PMP sub-brand, first mark out the four pitfalls
After talking about the big picture, let's go over a few pitfalls that people really fall into.
First, don’t confuse 'TPX sub-brand' with 'transparent PP'. Although PP transparent material is also clear, it cannot withstand sterilization temperatures of 220°C and will soften as soon as it enters the ethylene oxide sterilization chamber.
Second, look at the precipitates and ion content. When making medical or electronic products, even secondary brands need to check precipitate indicators; don't just go for the cheapest option.
Third, batch sampling. Even if the melt index between PMP batches differs slightly, the wall thickness of thin-walled dialyzer housings can fluctuate. Samples should be taken and trial molds made before entering the factory, and then full-scale production can begin.
Fourth, check the batch number. The original Mitsubishi TPX sub-brand batch number is traceable, while repackaged or re-bottled ones should be treated with a question mark.
Remember one thing: What PMP saves is money, what you can't afford to gamble on is the sterilizer round.
Cologne Warehouse Spot｜PMP Returning Customer
Main promoted brands: Mitsui Chemicals, Sumitomo Chemical, modified processing lineup (Ensinger/RTP/Westlake).
Main grades: TPX (RT18/MX002/MX004), Sumitomo high-purity PMP, TPX glass fiber reinforced/mineral-filled modified materials.
Packaging specifications: Small-pack secondary brands and boxed secondary brands use small packages, large-pack materials/ton bags use ton bags, and are packaged and stocked according to workshop usage.
Warehouse spot inventory: PMP warehouse spot inventory is usually around 5,000 tons, including 800-1,000 tons of small-package secondary brand stock, 300-500 tons of boxed secondary brand stock, and 3,500-3,900 tons of large-bag/ton-bag material stock.
Supply guarantee: test first, sign later; proceed with bulk goods only after the sample passes.
7. Selection mnemonic and a case from Lishui
Here are a few selection mnemonics for you:
Look at the usage—use the main brand for the highlight transparent cover, and consider the secondary brand for the inner tray.
Second, look at the indicators—precipitates, ions, light transmittance; not a single item can be overlooked for medical electronic components.
Third, check the batch number — original factory packaging, batch number traceable, if repackaged, put a question mark first;
Four checks for mold testing — first try a small sample mold, then run batch production on the machine, and increase volume only after the wall thickness is stable.
Let me tell a true story. There’s a client in Lishui that makes medical dialysis devices and sterilization trays. Previously, they bought a batch of questionable “TPX material” just to save costs. After sterilization, the shell deformation rate reached 8%, resulting in a batch return and a loss of over 200,000 yuan. Later, they switched to an original sub-brand under the Mitsui TPX system. Once the extractables and wall thickness indicators were aligned, the post-sterilization deformation rate was reduced to below 0.3%, and the yield increased from 70% to 95%.
This is the value of choosing the right model—PMP, when used correctly, saves money; when used incorrectly, it burns money. Ningbo Kolon New Materials Co., Ltd. has been working on imported polyolefin sub-brands for years and handles similar cases every year. To put it simply, it's about helping you smooth out the sterilization step before mass production.
Sources of information and data
1. Mitsui Chemicals Taiwan official website TPX (Polymethyl Pentene) product page, mitsuichemicals.com, verification date 2026-09-14.
2. PW Consulting, 'Worldwide Polymethylpentene (PMP) Market 2026,' pmarketresearch.com, verification date 2026-09-14.
3. Dataintelo, 'Poly 4 Methyl 1 Pentene Sales Market,' dataintelo.com, verification date 2026-09-14.
4. 24ChemicalResearch "Polymethylpentene (PMP) Market Outlook and Forecast 2026-2033", 24chemicalresearch.com, verification date 2026-09-14.
