科隆新材
中EN

波纹管用什么TPE/TPEE？原包码扫一下，真假见一半

应用领域 发布时间: 2026-09-16 938 阅读

The corrugated tube cracks after bending dozens of times, and the wire harness wears through and shorts, causing a shutdown. The corrugated tube was not chosen correctly for temperature resistance and flexibility, leaving the wires unprotected.

Bends dozens of times and it cracks, the wiring harness gets worn and shorts

Corrugated pipes are 'bending wire protection components': heat-resistant, flexible, and pressure-resistant. The material needs to be heat-resistant, flexible, and pressure-resistant — here's the conclusion first: conventional corrugated pipes mainly use TPE; for high-temperature wire protection, TPEE is preferred.

The biggest pitfall of corrugated pipes: scan the original package code, and you'll see half of the truth. Scan the original package code, and you'll see half of the truth—the original package code is the anti-counterfeiting line of the corrugated pipe.

Bellows are functional components: cracking and deformation are problems. Choosing the right material ensures cable stability—functional components, don't skimp on material costs.

Why choose TPE/TPEE for bellows?

Reasons for using TPE/TPEE for corrugated pipes: can withstand high temperatures, can be flexible, can resist pressure, high efficiency — together, these four make it suitable for corrugated pipes.

Temperature resistance is key: ambient temperature. Temperature resistance testing should be included in the acceptance criteria—deformation equals a problem.

Flexibility cannot be skipped: bend repeatedly. Include bending tests in the acceptance—if it cracks, it’s a problem.

Bending and compressive temperature resistance, three checkpoints

Bending conditions: repeated bending. Flexibility data must be tested—cracking indicates a problem.

Temperature working condition: ambient temperature. Temperature resistance data must be tested — deformation is the problem.

Pressure-resistant condition: Ballast protection. Pressure-resistant data must be tested—if it gets crushed, that's a problem.

TPE or TPEE? Corrugated tube comparison

DimensionTPETPEE
Temperature resistantCan doTall
FlexibleGoodGood
Pressure-resistantCan be doneGood
CostmiddleMedium-high
Wear-resistantmiddleStrong
PurposeRegularHigh temperature

Table reading: TPEE has good heat and wear resistance but is expensive; TPE has high cost-performance — standard corrugated pipe TPE, high-temperature TPEE.

Select by temperature: high temperature TPEE, regular TPE.

Bellows acceptance: scan the original package code first

ProjectCheckExplanation
Original package codeScan the QR codeVerification
Inkjet codingContrastconsistent
BatchTrace backVerification
Material propertiesRetestCheck

Reading the table: Check the original package code item by item to verify its authenticity—only accept the goods if the QR code on the bag, batch number, and production date all match.

The original package code is the security line of the corrugated tube.

Only looking at the price, three scams with counterfeit goods

Pitfall 1: Only care about the price. If the code scan doesn't match, the low price could be hiding counterfeit barrels — scanning the code is a must.

Pitfall 2: Missed temperature resistance test. Deformation — temperature resistance test, must be tested.

Pitfall three: Flexibility overstated. Cracking — bending should be inspected according to actual measurements.

Choose bellows material first for anti-counterfeiting

Three questions: Does it have the original packaging code, what is the temperature resistance, and how many times can it be bent? One test: Measured under actual working conditions—three questions and one test, the supplier's background is clear.

Anti-counterfeiting verification must come first: each bag should be scanned for the original package code before being stored. Scan first, then discuss the price — the original package code is the anti-counterfeiting line of the corrugated tube.

Making sample retention a habit: retain samples for each batch and re-test them according to batch with gentle and flexible methods. When changing materials between batches, compare first before scaling up—stable batches result in fewer customer complaints.

Bellows: Causes, Phenomena, and Countermeasures, All in One Table

PhenomenonReasonCountermeasure
CrackingInsufficient flexibilitySwitch to higher flexibility material
TransformationInsufficient temperature resistanceChange to heat-resistant material
SquashInsufficient stress resistanceSwitch to high compressive strength material
Doubt about authenticityOriginal package unclearScan code for verification
Batch DriftFormula fluctuationLock window

The conventional corrugated tube TPE bending radius gauge is within 4 times the inner diameter; if it is less than 4 times, it must hang for folding resistance. High-temperature wire protection only uses TPEE, which has a higher temperature resistance and is more expensive—choose the material grade according to the operating temperature.

TPE flexible and cheap, TPEE is much more expensive for temperature and fatigue resistance, don't use TPEE right away. Room temperature wiring TPE is sufficient; only above 120°C is TPEE irreplaceable—divided by temperature.

Bellows turn white and crack when folded in winter; first check low-temperature fold resistance, don't just look at appearance. Bending radius too sharp, bending data not measured, broken at outdoor project sites—flex resistance is based on real wiring radius for verification.

Bellows acceptance: temperature resistance, bending fatigue, joint seal leakage — a three-piece set. Scan the original package code one by one; if not scanned, it will not be accepted—export certification is based on batch verification.

Retain samples and verify physical properties, third-party testing completes the gap, and even if delivery is tight, deliver on time. Each batch of samples is tested for folding and temperature resistance; batch material changes are compared first and then scaled up.

Corrugated pipes are divided at 120°C, with TPE routing at room temperature and TPEE at high temperature. TPE is flexible and cheap, TPEE is more expensive in temperature and fatigue resistance, and if the bending radius is less than 4 times the wire diameter, it must be bent and seized. Use the actual wiring radius to check .

Scan the original package code individually, check the three-piece set for joint sealing and leakage. For winter folding that turns white, check for low-temperature fold resistance first; export certification is checked by batch; each batch retained sample tests fold resistance plus temperature resistance.

Temperature level is set at 120 degrees; if the original package code is scanned individually, it will not be accepted. Each batch of retained samples tests for folding and temperature resistance, bending radius is tested according to the real wiring core, joint sealing leakage three-piece set is tested together.

Folding resistance is measured according to the real wiring radius; too sharp bending will cause failure. Room temperature TPE high-temperature TPEE is separated by temperature, original package code scan the joint sealing leakage three-piece set,

Winter folding white first checks low-temperature fold resistance, each batch retained sample is foldable and heat-resistant.

Colum customer case: tight delivery deadline and in-stock mismatch, retained sample data for additional certification

An industrial equipment factory in Nanjing, corrugated pipe delivery time tight, in-stock grade and performance mismatched. Cologne cooperated by providing retained samples and physical property data for the same batch, performance verified accurately, passed third-party testing and supplementary certification, and delivered on schedule. Sample retention plus data, delivery deadlines tight, no worries—if performance doesn't match, verify the sample data first.

Summary

For bellows selection, scan the original package first, then test temperature resistance; scan the original package code to see half the truth; the original package code is an anti-counterfeit wire.

We never guess these three things: temperature resistance, lifespan, cost.

If you don't specify the operating temperature, don't guess; If you don't specify service life, don't guess; If you don't specify the quantity, don't guess. Any guessed plan will eventually be returned through rework and claims.

Ningbo Kelong New Materials Co., Ltd. produces modified thermoplastic elastomers, modified nylon (PA6 / PA66 / PA46 / PA11 / PA12 / PA6T / PA9T and nylon alloys), modified PPO / PPS, as well as nylon resins, sub-brand materials, and large package materials from major chemical giants in stock.

这台机器上的件，说下工况我帮你看看

报个件、说清温度和要过的认证，当天回你两三个能打的方案。电话微信同号，找到人就能聊。

打电话 18969817163发邮件询价

相关文章

汽车座椅护套用什么TPE？软不是全部，回弹才是应用领域行李架缓冲垫材质怎么选？报告会过期，批次不会应用领域# 汽车安全带导向环包胶用什么？良率上不去，先查烘料应用领域汽车线束扎带用什么弹性体？选错体系，成本多三成应用领域
WA