一根挤出的医疗导管，材料成本多花八毛，全年返工却省出两台设备的钱。这笔账，做挤出的都懂。
PA12（尼龙12）就是这么个材料：它长链、低吸水、耐油耐化学，挤出的导管软硬适中、弯不扁，是燃油管路和医疗导管的常客。可它正牌不便宜，一柜料压资金压得肉疼。
很多厂盯着副牌又下不去手——怕吸水、怕尺寸飘、怕挤出一炉管子壁厚忽厚忽薄。说白了，不是PA12副牌不能用，是你没搞懂它该怎么验。
这篇把PA12讲透：它和PA11差在哪，全球前三是哪几家，副牌做导管到底靠不靠谱。
长链尼龙里的“柔字派”
PA12是长链聚酰胺，酰胺基密度低，所以吸水率比PA6、PA66小一大截，尺寸更稳；韧性好、耐低温、耐油耐溶剂，挤出管材软而不塌。它常和PA11放一起说——俩都是长链，都耐油，但PA12主原料是丁二烯路线，成本通常比蓖麻油路线的PA11友好一些。
燃油管路、气动管、医疗导管、3D打印粉末，都是它的主场。
全球PA12格局，前三很清晰：德国赢创（Evonik）的VESTAMID®常年领跑，份额约两成；法国阿科玛（Arkema）的Rilsan®/Rilsamid®紧随其后；瑞士EMS-GRIVORY的Grilamid® L排第三。日本宇部兴产在第二梯队。三家都在非中国大陆。
副牌是同一根长链，只是化验单某格没踩线
PA12副牌，是同一厂、同一牌号里，熔指、含水率或某项力学指标出厂检验小幅偏离的批次。长链分子结构和正牌一致，还是原厂原生料。
四条来源不变：开停车头尾料、牌号切换过渡料、工艺波动致单项超标的批次、副线尾料。
边界要分清：正牌全指标达标；副牌单项小幅浮动；回料是挤出管边角再造粒，已经受过热历史；再生料波动大。PA12挤出怕含水率和熔指飘——含水率高了管子起泡、表面麻点，熔指飘了壁厚不稳。这两点，就是验收的关键。
副牌主题金句：PA12副牌挤出来的医疗导管，壁厚均匀、耐水解耐化学，装机半年弯不扁也不渗液。
赢创：VESTAMID®，长链尼龙的头部
赢创的VESTAMID®是PA12标杆，挤出级、注塑级、3D打印粉末级都很全，医疗导管和燃油管都认它。它的副牌多是熔指或色相小幅偏离的批次，基材一致。
做非医疗接触的工业管、一般挤出型材，挑它的精选副牌，资金压力小很多。
阿科玛：Rilsan®，燃油管路的老招牌
阿科玛的Rilsan®/Rilsamid®是燃油系统用PA12的老招牌，耐油耐渗透是强项，透明和生物基牌号也在扩。它的副牌批次规整，挤出稳定性口碑不错。
做普通气动管、护套挤出，用它的副牌性价比实在。
EMS-GRIVORY：Grilamid® L，精密件的老手
瑞士EMS-GRIVORY的Grilamid® L系列，在精密注塑和管材上用得很细，力学和尺寸稳定性讲究。它的副牌适合对外观和尺寸有要求但不追认证的挤出件。
PA12副牌做导管，先过这三道关
头一条，含水率先测。挤出前必须烘料到位，含水率超标，管子表面起泡麻点，一炉料全废。副牌更要把干燥工艺卡严。
再一条，熔指对牌号。挤出管看熔指，注塑件看流动。拿错熔指的副牌，壁厚和充模都飘。
还有一条，医疗接触件走正牌。要灭菌、要生物相容性的导管，别用副牌硬冲，认证过不了代价太大。
科隆仓库现货｜PA12常规
主推品牌：赢创、阿科玛、EMS-GRIVORY
主要牌号：VESTAMID系列、Rilsan/Rilsamid系列、Grilamid L系列
包装规格：大包装/小包装均有备货
仓库现货通常在4000吨上下
小包副牌备货600-900吨、箱装副牌备货250-450吨、大包料/吨包料备货2650-3150吨
供应保障：检测单随货
六条口诀，挤出厂照着下单
1. 医疗接触、要灭菌认证——走正牌，副牌别碰
2. 工业管、气动管、护套——原厂副牌可以上
3. 进厂先烘料测含水率——防起泡麻点
4. 按挤出/注塑选熔指——别拿错牌号
5. 认准原厂大包装/小包装，批次留样
6. 小批量试挤——壁厚尺寸先验再放量
福州有家做医用引流导管的客户，之前用某国产料挤出，含水率控不稳，管子表面隔三岔五出麻点，客户抽检退货率一度到8%。后来换成赢创和阿科玛的原厂副牌挤出级，进厂严格烘料测含水率、按批次留样，退货率压到0.4%，挤出良率拉上来之后，单线产能还多跑了一成。
这就是选型的价值——PA12副牌不是不能用，是得把含水率和熔指卡准。宁波市科隆新材料有限公司做进口大厂副牌料多年，这种“管子泡不泡、壁厚稳不稳”的案子，每年处理不少，说白了就是帮你在量产前把挤出那口气顺过来。
做挤出管的、做医疗导管的、做燃油管的，谁没被PA12坑过？
是管子表面起麻点、客户抽检退回？还是壁厚忽厚忽薄、截下来长短不齐？或者吸水后尺寸飘、装机就漏？
资料与数据来源
Dataintelo：Polyamide 12 Market（Evonik约18.2%、Arkema约15.7%份额口径）
24ChemicalResearch：Nylon 12 Resin Market（Evonik、Arkema、EMS-GRIVORY、UBE主要厂商）
PW Consulting：Global PA12 Resin Market 2026（Arkema Rilsamid®、EMS-GRIVORY Grilamid® L）
Verified Market Reports：PA 12 Market（Evonik、Arkema、EMS-GRIVORY、UBE 四大头部）
An extruded medical catheter costs an extra eighty cents in material, but reworking it throughout the year saves the cost of two machines. Those who do extrusion all understand this calculation.
PA12 (Nylon 12) is exactly this kind of material: it has long chains, low water absorption, and is oil- and chemical-resistant. The extruded tubing is moderately soft and hard, and it bends without flattening, making it a common choice for fuel lines and medical catheters. But the genuine material is not cheap, and stocking a whole container of it puts a painful strain on cash flow.
Many factories are eyeing secondary brands but hesitate to take action—they worry about water absorption, size variation, and the extruded batch of pipes having inconsistent wall thickness. To put it bluntly, it's not that PA12 secondary brands can't be used; it's that you don't understand how to test them.
This article explains PA12 thoroughly: how it differs from PA11, which are the top three companies globally, and whether sub-brands making catheters are reliable.
'Soft School' in Long-chain Nylon
PA12 is a long-chain polyamide with a low amide group density, so its water absorption is much lower than that of PA6 and PA66, making its dimensions more stable; it has good toughness, low-temperature resistance, and resistance to oil and solvents, and extruded pipes are soft but do not collapse. It is often mentioned together with PA11 — both are long-chain and oil-resistant, but PA12's main raw material is derived from the butadiene route, which is usually more cost-friendly compared to the castor oil route of PA11.
Fuel pipelines, pneumatic pipes, medical catheters, and 3D printing powders are all its forte.
The global PA12 landscape has a very clear top three: Germany's Evonik leads with VESTAMID® for many years, holding about 20% market share; France's Arkema with Rilsan®/Rilsamid® follows closely; Switzerland's EMS-GRIVORY ranks third with Grilamid® L. Japan's Ube Industries is in the second tier. All three are outside mainland China.
The secondary test strip is the same long chain, it's just that one square on the test report didn't reach the line.
PA12 secondary grade refers to batches from the same manufacturer and the same grade number where melt index, moisture content, or some mechanical indicators slightly deviate from the factory inspection. The long-chain molecular structure is consistent with the standard grade, and it is still original material from the original factory.
Four sources remain unchanged: material from the beginning and end of stopping production, transition material during grade switching, batches exceeding individual standards due to process fluctuations, and leftover material from secondary lines.
Boundaries must be clear: official brands fully meet the standards; subsidiary brands have slight fluctuations in individual indicators; regrind is made by re-pelletizing extrusion tube scraps and has already been exposed to previous heat; recycled material fluctuates greatly. PA12 extrusion is sensitive to moisture content and melt flow index drift—if the moisture is too high, pipes will bubble and have surface pitting, and if the melt index drifts, wall thickness will be unstable. These two points are the key for acceptance.
Subtitle theme catchphrase: Medical catheters extruded from PA12 secondary grade, with uniform wall thickness, hydrolysis and chemical resistant, still not bent, flattened, or leaking after being installed for half a year.
Evonik: VESTAMID®, the leader in long-chain nylon
Evonik's VESTAMID® is the benchmark for PA12, with a full range of grades for extrusion, injection molding, and 3D printing powders. It is recognized for medical catheters and fuel lines. Its sub-brands mostly have batches with slightly different melt indices or color shades, but the base material is consistent.
For non-medical contact industrial pipes and general extruded profiles, choose its selected sub-brand, which has much less financial pressure.
Arkema: Rilsan®, the classic name in fuel lines
Arkema's Rilsan®/Rilsamid® is a well-established PA12 for fuel systems, with strengths in oil resistance and low permeability, and the transparent and bio-based grades are also expanding. Its secondary grades have uniform batches, and its extrusion stability has a good reputation.
For ordinary pneumatic tubes and sheath extrusion, using its secondary brand is really cost-effective.
EMS-GRIVORY: Grilamid® L, a veteran in precision parts
The Grilamid® L series from Swiss EMS-GRIVORY is used in precision injection molding and tubing, with a focus on mechanical properties and dimensional stability. Its sub-brand is suitable for extruded parts that require appearance and dimensions but do not pursue certification.
Using PA12 secondary card to make a conduit, go through these three steps first
First point, measure the moisture content first. Before extrusion, the material must be properly dried; if the moisture content exceeds the standard, the surface of the pipe will blister and have pimples, and the entire batch of material will be wasted. For secondary brands, the drying process must be strictly controlled.
One more thing, match the melt flow index with the grade. Check the melt flow index on the extruded tube, and observe the flow on the injection-molded part. Using the wrong melt flow index for the substitute grade will cause the wall thickness and mold filling to be unstable.
One more thing, medical contact parts should use the genuine brand. For catheters that need to be sterilized and biocompatible, don't use knock-off brands recklessly; failing certification is too costly.
Cologne Warehouse Spot｜PA12 Standard
Main promoted brands: Evonik, Arkema, EMS-GRIVORY
Main grades: VESTAMID series, Rilsan/Rilsamid series, Grilamid L series
Packaging specifications: Both large and small packages are available in stock
The warehouse spot goods are usually around 4,000 tons.
Small package secondary brand stock 600-900 tons, box-packed secondary brand stock 250-450 tons, large package material/ton package material stock 2650-3150 tons
Supply Assurance: Test Report Accompanies the Goods
Six tips, squeeze them out of the factory and place the order accordingly
1. Medical contact, requires sterilization certification — go for the genuine brand, avoid the secondary brand
2. Industrial pipes, pneumatic pipes, protective sleeves — original factory secondary brands are acceptable
3. Dry the materials and measure moisture content before entering the factory — to prevent foaming and pitting
4. Choose the melt index according to extrusion/injection molding — don’t pick the wrong grade
5. Make sure to identify the original factory large/small packaging, and keep a sample from each batch
6. Small batch trial extrusion — wall thickness dimension verified before scaling up
There is a client in Fuzhou that manufactures medical drainage catheters. Previously, they used a certain domestic material for extrusion, but the moisture content was unstable, and tiny bumps would frequently appear on the surface of the tubes. The client’s inspection rejection rate once reached 8%. Later, they switched to Dow and Arkema's original factory subsidiary brands for extrusion grades, strictly dried the materials and measured the moisture content upon arrival, and kept samples by batch. The return rate dropped to 0.4%, and after improving the extrusion yield, the single-line production capacity increased by another 10%.
This is the value of selecting the right type — PA12 secondary brand is not unusable, but the moisture content and melt index need to be calibrated correctly. Ningbo Kolong New Materials Co., Ltd. has been producing secondary materials of imported major brands for many years. Cases like 'whether the tube bubbles or whether the wall thickness is stable' are handled frequently every year. Simply put, it helps you smooth out the extrusion process before mass production.
Who hasn’t been screwed over by PA12 when making extrusion tubes, medical catheters, or fuel pipes?
Is it that the surface of the pipe has pitting, and the customer rejected it after sampling? Or is it that the wall thickness is uneven, and the cut pieces are of varying lengths? Or does it change size after absorbing water, causing leaks when installed?
Sources of information and data
Dataintelo: Polyamide 12 Market (Evonik approximately 18.2%, Arkema approximately 15.7% market share)
24ChemicalResearch: Nylon 12 Resin Market (Main manufacturers: Evonik, Arkema, EMS-GRIVORY, UBE)
PW Consulting: Global PA12 Resin Market 2026 (Arkema Rilsamid®, EMS-GRIVORY Grilamid® L)
Verified Market Reports: PA 12 Market (The four major players: Evonik, Arkema, EMS-GRIVORY, UBE)
