再生HIPS聚苯乙烯：家电内衬文具外壳，再生料良率也能稳住

又到开学前的赶单季，文具厂的注塑机二十四小时不歇；金九银十一到，家电厂的塑料内衬、外壳订单也跟着爆。越是这种赶工的时候，老板们越头疼——料价一涨，利润就被挤薄，可换再生料又怕良率掉下来，赔了夫人又折兵。今天就把再生HIPS这档子事说透：它到底能不能稳得住良率，路又该怎么走，哪些件放心用、哪些件得留个心眼。

先花两分钟认识下主角。宁波市科隆新材料有限公司是一家工贸一体的塑料原料供应企业，长期做再生塑料原料，品类覆盖PP、PE、ABS、PC、PET、PVC、HIPS等多个方向。今天的主角是再生HIPS，学名抗冲击聚苯乙烯。HIPS你天天见：电视机后背板、冰箱里的内衬、笔盒文具盒、玩具车外壳、相框镜框，大多是它做的。它的底子是透明发脆的通用聚苯乙烯（GPPS），厂家在聚合时掺进了橡胶颗粒增韧，所以比普通PS耐摔、抗冲击，又保留了PS好注塑、易着色、尺寸稳的优点。它的再生来源也很清楚：废旧家电外壳、电视机背板、CD盒、文具玩具回收，经过分选、清洗、熔融造粒，就成了再生HIPS。GB/T 40006.6—2021《塑料再生塑料第6部分：聚苯乙烯（PS）和抗冲击聚苯乙烯（PS-I）材料》就是给它立的规矩，2022年5月起正式实施。

再生HIPS怕的不是旧，是橡胶被磨没了

很多人一听“再生HIPS”，就觉得“回料，肯定脆，一摔就裂”。这话点到了一半，却没说透根子在哪。HIPS耐不耐摔，靠的是分散在基体里的那一颗颗橡胶颗粒——它们像弹簧一样吸收冲击力，不让裂纹扩展。问题就出在这：橡胶这东西，每经历一次高温熔融，就会老化降解一点。再生HIPS已经走过一轮加工，橡胶含量和橡胶颗粒的完整性都打了折扣，所以多次回收的料，抗冲击强度确实会往下掉。

但这不是说再生HIPS不能用，而是说你得搞清楚“这批料的橡胶还剩多少”。行业里有个很直观的分法：按简支梁缺口冲击强度来分，低于5kJ/m²的算品质偏低，达到5kJ/m²以上才算品质过得去的高冲级。GB/T 40006.6—2021把颗粒外观、灰分、水分、熔体流动速率（MFR）变异系数、拉伸强度、维卡软化温度、残留苯乙烯单体含量都列进了考核项。你看，标准卡的从来不是“回收两个字”，而是“性能还剩几成”。性能剩下的多，就做家电面板；剩下的少，就去做对冲击要求不高的文具、内衬。各归各位，这才是再生HIPS正确的打开方式。还有个采购经常忽略的点——残留苯乙烯单体。聚苯乙烯加工和回收过程中，可能残留少量未反应的苯乙烯单体，标准里专门列了这项。做普通工业件无所谓，但如果你的制品要跟食品、儿童用品沾边，这项就得测、就得控。别觉得“反正都是PS，能有什么事”，真过检的时候，这项数据拿不出来，整批货都得压着。

再补一句很多采购不知道的事：HIPS和GPPS长得像，回收时必须分开。GPPS脆、透明，HIPS韧、半透或乳白；同一条清洗线上混了GPPS，做出来的HIPS抗冲击就会被拉低。所以正规再生HIPS厂，进厂先做材质分选，把GPPS、ABS、其他塑料剔出去，留下干净的HIPS再造粒。分选这一步省了，后面再怎么改性都补不回来。

图1　再生HIPS注塑件生产线

注塑料和发泡料，再生后走的根本不是一条路

要把再生HIPS听懂，得先把“注塑”和“发泡”这两条路分开。这两条路用的虽然都是聚苯乙烯家族的料，但再生之后的脾气完全不一样。

注塑路的料，主打一个“好成型、能着色”。废旧家电背板、文具外壳回收回来，分选、清洗、造粒之后，MFR（熔体流动速率）要稳，否则同一模次出来的件厚薄不一、缺胶飞边。家电厂常按15%到40%的比例把再生HIPS掺进新料里做白色家电面板，既降了本又不影响外观和强度；要求不高的办公用品、展示架、教育器材，甚至能纯再生直接注塑。这条路的关键，是MFR稳不稳、颜色均不均、冲击够不够。

发泡路的料，走的是另一个逻辑。它多用EPS发泡泡沫、缓冲包装回收，再生后要重新发泡，关注的是发泡倍率、泡孔均匀度、密度稳不稳。发泡料对冲击强度要求没注塑那么高，但对杂质很敏感——混进去别的塑料，泡孔就塌、就破。所以发泡级再生PS往往单独走一条线，不跟注塑料混。把这两条路搞混，是再生PS采购里常见的乌龙：拿注塑料去发泡，发不起来；拿发泡料去注塑，表面全是泡。

整条再生线的工序并不神秘：废旧HIPS制品先人工加机器分选，按颜色、材质把HIPS从一堆塑料里挑出来，剔除GPPS和ABS；接着破碎、清洗，把灰尘、油污、标签纸洗干净；然后熔融挤出造粒，拉条、水冷、切粒成规整的颗粒。工艺听着不复杂，难的是稳定——颜色杂的要配色，MFR飘的要复配，冲击不够的要补增韧。正规厂会在造粒前后加检测，把灰分、水分、MFR、冲击一项项卡出来，再分级包装。这也是为什么同样叫“再生HIPS”，不同厂的货差价不小：差的就是分选、清洗、检测这几道功夫下没下够。

宁波市科隆新材料有限公司对接客户时，习惯先问一句：你是注塑件还是发泡件？就这一句，能帮客户避开大半选型错误。下面这张表，把常见再生HIPS/PS等级按用途理清，数据依据GB/T 40006.6—2021及行业公开资料整理。

等级名称	主要来源/工艺	关键指标	典型用途
高冲级再生HIPS	电视背板/家电外壳回收改性	缺口冲击≥5.5kJ/m²，MFR约2.0—4.5，灰分低	白色家电面板、显示器背板
通用注塑级再生HIPS	文具/玩具/日用品回收	冲击中等，易加工、易着色	文具外壳、玩具、镜框
本色/浅灰再生HIPS	家电内衬/CD盒清洁回收	色泽一致，可配色	家电内衬、吸塑片材
黑色阻燃再生HIPS	电子外壳阻燃料回收	阻燃达标，冲击合格	电器外壳、设备内部件
再生GPPS透明白料	CD盒/透明制品回收	浅色透明，流动性好	透明文具、相框、一次性制品
发泡级再生PS	EPS泡沫/缓冲包装回收	发泡倍率、泡孔密度可控	发泡包装、缓冲材料

表注：以上依据GB/T 40006.6—2021《塑料再生塑料第6部分：聚苯乙烯（PS）和抗冲击聚苯乙烯（PS-I）材料》及行业公开资料整理；标准对灰分、水分、MFR变异系数、残留苯乙烯单体等均有要求。更多等级与物性参数以厂家官方TDS为准，选型前建议索取近期第三方检测报告。

良率稳不稳，就看MFR这一条线

再生HIPS的降本账，跟别的料有点像，又不太像。像的是料价——再生HIPS比新HIPS便宜一截，文具、玩具、内衬这些走量件，用它确实能压成本。不像的是，它对“批次一致性”特别敏感。HIPS注塑本来就靠MFR定工艺，再生料如果MFR忽高忽低，上一模还好好的，下一模就缺胶、飞边、缩水，车间就得跟着调机，良率哗哗往下掉。所以买再生HIPS，别只问价格，先要MFR的批次波动数据。

再把账摊开算：新HIPS树脂料价高但批次稳，做高要求外观件放心；再生HIPS料价低，但前期要留调机成本，批次要靠检测报告兜着。对文具、玩具、内衬这些走量、外观要求不极端的件，再生料掺进去，良率稳住就是纯利润；对外观零瑕疵、外露的高端件，要么选本色一致级高冲料，要么就老老实实用新料。别抱着“再生料万能”的念头，也别抱着“再生料必烂”的偏见——说白了，它就是一种得对等级、得管批次的普通原料而已，别神化它，也别一棍子打死。

成本项	新料原生HIPS	再生HIPS（对等级）	差异说明
原料采购价	基准价	低一截	再生料主要优势，文具/内衬走量明显
批次稳定性	MFR窄、波动小	取决于分选与造粒	要MFR波动数据才稳得住
加工良率	稳定	初期需调机	MFR、杂质不稳直接反映在废品率
外观/配色	均匀	易带杂色	本色一致级贵，杂色级便宜
抗冲击保持	高	随再生次数下降	高冲级够，多次回用料偏脆
综合成本	高	走量场景更低	算上良率和退货再下结论

边界清单：

放心用：文具外壳、玩具、相框镜框、家电内衬、吸塑片材、展示架、教育器材，这些是再生HIPS的主场，量大、对成本敏感，用对等级就是实实在在的降本。

要留心：白色家电面板，按15%—40%比例掺新料兜底，盯冲击和色差；对外观要求高的浅色件，选本色一致级。

别碰：对长期抗冲击、外观零瑕疵有高要求的外露结构件，别用多次回收的偏脆料；发泡件和注塑件别串用；接触食品的制品另需符合相应食品接触标准。

良率不是靠运气，是靠每批都对上数

下面这情形，做注塑的多半不陌生（人物情节已做合并简化）。宁波周边一家做文具外壳的注塑厂，前几年一直在再生HIPS上栽跟头：贪便宜进了一批杂色再生料，上机才发现MFR忽高忽低，做出来的笔盒一批厚一批薄，还带着杂色斑点，喷涂都盖不住，废品率居高不下。换了几家供应商，问题依旧——因为他们一直只比价，没要过MFR的批次数据。

走投无路之际，他们抱着试试的心态找到了宁波市科隆新材料有限公司。科隆新材接下这单后没急着报价，先摸清了产品是注塑文具外壳、对颜色和冲击要求不高，再按通用注塑级去对货：每批附检测报告，MFR波动压在窄区间，冲击强度达标，颜色还能按客户的灰度值微调。换料之后，注塑参数不用天天调，笔盒厚薄均匀、杂色斑没了，废品率明显降下来，喷涂成本也省了一块。这厂后来就固定按这套方式对货，再生料的良率算是真正稳住了，老板再不用每批货到了先提心吊胆。

再生HIPS能不能用，不看它便不便宜，看它每批是不是都一样。MFR、冲击、颜色这三样，每批都对上数，良率自然稳。还有一点值得留意：再生料别一次掺太猛，先从两三成试起，跑顺了再慢慢加比例，给车间和模具一个适应的过程，比一上来就满掺稳当得多。

（注：本段为选型思路演示用的合成案例，人物厂名均非真实对应。）

先定注塑还是发泡，料的位置自然就清楚了

选料前，把下面这张表存进手机，遇到对号入座就行。用之前再啰嗦一句：不管选哪个等级，都记得跟供应商要三样东西——MFR的批次数据、缺口冲击强度、颜色一致性说明。这三样齐了，再生HIPS的良率就不会出大问题。

应用场景	推荐等级	注意事项	何时别用
白色家电面板/背板	高冲级再生HIPS	按比例掺新料，盯冲击色差	纯再生做高外观外露件
文具外壳/玩具	通用注塑级再生HIPS	MFR要稳，颜色可微调	杂色料做浅色外观件
家电内衬/吸塑片	本色浅灰再生HIPS	色泽一致、无杂质	杂质多的料做吸塑
电器内部件	黑色阻燃再生HIPS	阻燃与冲击双达标	非阻燃料做有阻燃要求件
透明文具/相框	再生GPPS透明白料	杂质少、透光好	杂色再生料做透明件
发泡包装/缓冲	发泡级再生PS	单独走发泡线	注塑料拿去发泡

再生HIPS，家电内衬和文具外壳的性价比之选

声明：本文提及的品牌及商标权归各自原厂所有。本文为第三方选材知识分享，文中涉及的具体等级、参数、价格、认证等信息以各厂家官方最新资料为准。本文不构成任何采购或投资建议。

It's the rush order season before the new school term again, and the injection molding machines at stationery factories are running 24 hours nonstop; with 'Golden September and Silver November' arriving, orders for plastic liners and housings at home appliance factories are also booming. The more it's a rush period, the more headaches the bosses have — when material prices rise, profits get squeezed, but if they switch to recycled materials, they're worried about yield dropping, ending up at a double loss. Today, let's talk thoroughly about recycled HIPS: whether it can really stabilize the yield, what path to take, which parts are safe to use, and which parts need extra caution.

Let's spend two minutes getting to know the main subject. Ningbo Cologne New Materials Co., Ltd. is an integrated trade and industrial enterprise that supplies plastic raw materials, focusing long-term on recycled plastic raw materials, with product ranges covering PP, PE, ABS, PC, PET, PVC, HIPS, and other types. Today's main subject is recycled HIPS, scientifically known as high-impact polystyrene. You encounter HIPS every day: the back panels of TVs, refrigerator liners, pencil boxes, stationery boxes, toy car shells, and picture frames are mostly made of it. Its base material is transparent and brittle general-purpose polystyrene (GPPS), and during polymerization, manufacturers mixed in rubber particles to toughen it, making it more impact-resistant than ordinary PS while retaining PS's advantages of good injection molding, easy coloring, and dimensional stability. Its recycled sources are also clear: old appliance shells, TV back panels, CD cases, and recovered stationery and toys that, after sorting, cleaning, and melting into pellets, become recycled HIPS. GB/T 40006.6—2021 "Plastics — Recycled Plastics — Part 6: Polystyrene (PS) and High-Impact Polystyrene (PS-I) Materials" is the standard established for it, and it has been officially implemented since May 2022.

What recycled HIPS fears is not being old, but the rubber being worn away.

Many people, when they hear 'recycled HIPS,' immediately think 'it's recycled, it must be brittle, it'll crack if dropped.' This statement hits halfway but doesn't get to the root of the matter. Whether HIPS is resistant to impact depends on the tiny rubber particles dispersed throughout the matrix—they act like springs to absorb shock and prevent cracks from spreading. The problem lies here: rubber, every time it experiences high-temperature melting, will age and degrade a bit. Recycled HIPS has already gone through one processing cycle, so both the rubber content and the integrity of the rubber particles are reduced. Therefore, materials that have been recycled multiple times do indeed see a drop in impact strength.

But this doesn't mean that recycled HIPS can't be used; it just means you need to figure out 'how much rubber is left in this batch.' There's a very straightforward classification in the industry: it is based on the notched impact strength of a simply supported beam. If it is below 5kJ/m², it is considered low-quality; if it reaches above 5kJ/m², it is considered a high-impact grade with acceptable quality. GB/T 40006.6—2021 lists evaluation items including pellet appearance, ash content, moisture content, melt flow rate (MFR) variation coefficient, tensile strength, Vicat softening temperature, and residual styrene monomer content. You see, the standard doesn't focus on the word 'recycled,' but on 'how much performance is left.' If much performance remains, you use it for appliance panels; if less remains, it goes into stationery or liners that don't require high impact resistance. Each type has its proper application – this is the correct way to use recycled HIPS. Another point often overlooked by purchasers is residual styrene monomer. During polystyrene processing and recycling, a small amount of unreacted styrene monomer may remain, and the standard specifically lists this. For ordinary industrial products, it doesn’t matter, but if your products come into contact with food or children's items, this must be measured and controlled. Don’t think 'it's all PS anyway, what could go wrong.' When it comes to inspection, if you can’t provide this data, the entire batch will be held back.

One more thing that many purchasers don't know: HIPS and GPPS look similar, but they must be separated during recycling. GPPS is brittle and transparent, while HIPS is tough and semi-transparent or milky; if GPPS gets mixed in on the same washing line, the impact resistance of the resulting HIPS will be reduced. Therefore, at a proper recycled HIPS factory, materials are sorted when they arrive, with GPPS, ABS, and other plastics removed, leaving clean HIPS for granulation. If this sorting step is skipped, no amount of later modification can make up for it.

Figure 1　Recycled HIPS Injection Molding Production Line

Injection molding materials and foaming materials, after recycling, fundamentally do not follow the same path.

To understand recycled HIPS, you first need to separate the two paths of 'injection molding' and 'foaming.' Although both paths use materials from the polystyrene family, the nature of the material after recycling is completely different.

For injection molding materials, the focus is on being 'easy to mold and able to be colored.' Recycled back panels from old appliances and outer shells of stationery are collected, sorted, cleaned, and granulated. The MFR (melt flow rate) needs to be stable; otherwise, parts from the same mold run will come out with uneven thickness or have short shots and flash. Appliance manufacturers often mix recycled HIPS into new material at a ratio of 15% to 40% to make white appliance panels, which lowers cost without affecting appearance or strength. For less demanding office supplies, display racks, and educational tools, even 100% recycled material can be directly injection molded. The key on this path is whether the MFR is stable, the color is uniform, and the impact strength is sufficient.

Foaming material follows a different logic. It mainly uses EPS foam, cushioning packaging for recycling, and after regeneration, it needs to be re-foamed, focusing on the foaming ratio, uniformity of pores, and density stability. Foamed material does not require as high impact strength as injection molding, but it is very sensitive to impurities—if other plastics get mixed in, the pores will collapse or break. Therefore, regenerated PS for foaming often runs on a separate line and is not mixed with injection molding material. Confusing these two routes is a common blunder in purchasing recycled PS: using injection molding material for foaming doesn’t expand; using foamed material for injection molding results in a surface full of bubbles.

The entire recycling line process is not mysterious: waste HIPS products are first sorted manually and mechanically, separating HIPS by color and material from a pile of plastics, removing GPPS and ABS; then they are crushed and washed to clean off dust, oil, and labels; next, they are melted, extruded, and pelletized, drawn into strands, water-cooled, and cut into uniform pellets. The process doesn't sound complicated, but the challenge is in stability—materials with mixed colors need color matching, fluctuating MFR requires adjustment, and insufficient impact resistance needs toughening additives. Reputable factories conduct tests before and after pelletizing, checking ash content, moisture, MFR, and impact one by one, then grade and package accordingly. This is why even though products may all be called 'recycled HIPS,' prices vary significantly between manufacturers: the difference lies in the thoroughness of sorting, cleaning, and testing.

When Ningbo Kolong New Materials Co., Ltd. communicates with customers, they usually start by asking: Are you using injection-molded parts or foamed parts? Just this one question can help customers avoid most selection mistakes. The table below organizes common recycled HIPS/PS grades according to their uses, based on GB/T 40006.6—2021 and publicly available industry data.

Level Name	Main Sources / Processes	Key indicators	Typical uses
High-impact grade recycled HIPS	Television Back Panel/Home Appliance Housing Recycling and Modification	Notch impact ≥5.5 kJ/m², MFR approximately 2.0–4.5, low ash content	White appliance panels, monitor backplates
General-purpose injection molding grade recycled HIPS	Stationery/Toys/Daily Necessities Recycling	Medium impact, easy to process, easy to color	Stationery cases, toys, eyeglass frames
Natural/Light Gray Recycled HIPS	Home Appliance Liners / CD Case Cleaning and Recycling	Consistent color, can be matched	Appliance lining, blister sheet
Black flame-retardant recycled HIPS	Recycling of flame-retardant materials in electronic casings	Flame-retardant meets standards, impact test passed	Electrical appliance housings, internal components of equipment
Recycled GPPS Transparent White Material	CD cases/transparent products recycling	Light-colored and transparent, with good fluidity	Transparent stationery, photo frames, disposable products
Foam-grade recycled PS	EPS Foam/Cushion Packaging Recycling	Foaming ratio and pore density are controllable	Foam packaging, cushioning materials

Note: The above is compiled based on GB/T 40006.6—2021 'Plastics — Recycled Plastics Part 6: Polystyrene (PS) and High-Impact Polystyrene (PS-I) Materials' and publicly available industry information; the standard sets requirements for ash content, moisture content, MFR variation coefficient, residual styrene monomer, etc. For more grades and physical property parameters, please refer to the manufacturer's official TDS. It is recommended to request recent third-party test reports before selecting materials.

Whether the yield is stable or not depends on the MFR line.

The cost-saving account of recycled HIPS is somewhat similar to other materials, yet not quite the same. The similarity lies in the price — recycled HIPS is cheaper than virgin HIPS, so using it for volume items like stationery, toys, and linings can indeed reduce costs. The difference is that it is particularly sensitive to 'batch consistency.' HIPS injection molding normally relies on MFR to set the process, and if the MFR of recycled material fluctuates too much, one mold may be fine, but the next could have issues like insufficient material, flash, or shrinkage, forcing the workshop to adjust the machines constantly, and the yield drops rapidly. Therefore, when purchasing recycled HIPS, don’t just ask for the price; first, check the batch-to-batch MFR variation data.

Let's break down the costs: New HIPS resin is expensive but has stable batches, making it reliable for high-demand appearance parts; recycled HIPS is cheaper, but you need to account for the machine adjustment costs upfront, and batch consistency depends on inspection reports. For stationery, toys, and liners—high-volume items with non-critical appearance requirements—mixing in recycled material can stabilize yield and directly increase profit; for high-end parts that need flawless, exposed appearances, you either choose high-impact material with consistent natural color or just honestly use new material. Don’t cling to the idea that "recycled material is万能 (all-purpose)", and don’t hold the prejudice that "recycled material is必烂 (bound to be bad)"—plainly speaking, it’s just an ordinary raw material that requires proper grading and batch control. Don’t overhype it, and don’t dismiss it outright.

Cost item	New virgin HIPS	Recycled HIPS (Grade)	Difference Explanation
Raw material purchase price	Benchmark price	a bit lower	The main advantage of recycled materials is that stationery/lining has obvious sales volume.
Batch stability	MFR narrow, small fluctuation	Depends on sorting and granulation	Only with MFR fluctuation data can it be stable
Processing yield	Stable	Initial machine adjustment required	MFR and unstable impurities are directly reflected in the scrap rate
Appearance/Color Scheme	Even	Prone to mixed colors	The naturally consistent grade is expensive, while the mixed color grade is cheap.
Impact resistance retention	Tall	Declines with the number of regenerations	The high shock level is sufficient, and repeated use makes the material brittle.
Comprehensive cost	Tall	Lower volume scenario	Make the conclusion after considering yield rate and returns

Boundary List:

Safe to use: Stationery casings, toys, photo frame and mirror frames, appliance linings, blister sheets, display racks, and educational equipment — these are the main applications for recycled HIPS. High volume and cost-sensitive, using the right grade is a real way to reduce costs.

Be careful: For white home appliance panels, mix new material at a ratio of 15%–40% as a safeguard, and monitor for impact resistance and color difference; for light-colored parts with high appearance requirements, choose a grade consistent with the original color.

Do not touch: For exposed structural parts that require long-term impact resistance and flawless appearance, do not use repeatedly recycled brittle materials; foam parts and injection-molded parts should not be mixed; products that come into contact with food must also comply with the relevant food contact standards.

Yield is not based on luck; it's based on matching the numbers for each batch.

The following situation is probably familiar to many who work in injection molding (characters and plot have been merged and simplified). An injection molding factory around Ningbo that produces stationery casings had been struggling with recycled HIPS for several years: to save money, they purchased a batch of mixed-color recycled material, only to find out after processing that the MFR fluctuated greatly. The produced pencil cases were uneven in thickness and had specks of mixed colors that couldn't be covered even with spraying, resulting in a high scrap rate. They switched suppliers several times, but the problem persisted—because they had only compared prices and never requested batch data for the MFR.

At a dead end, they decided to give it a try and approached Ningbo Kolon New Materials Co., Ltd. After taking on the order, Kolon New Materials didn’t rush to quote. They first figured out that the product was an injection-molded stationery shell, with low requirements for color and impact strength, and then handled the materials according to general injection molding standards: each batch included a test report, MFR fluctuations were kept within a narrow range, impact strength met standards, and the color could be slightly adjusted according to the customer's gray scale. After switching materials, the injection molding parameters no longer needed daily adjustments, the pen cases had uniform thickness, no color spots, the defect rate dropped noticeably, and painting costs were reduced. This factory later continued to handle materials using this method consistently, and the yield of recycled materials truly stabilized, so the boss no longer had to worry every time a batch arrived.

Whether recycled HIPS can be used or not doesn't depend on whether it's cheap; it depends on whether each batch is consistent. If MFR, impact, and color match for each batch, the yield will naturally be stable. Another point to note: don't mix in too much recycled material at once. Start with 20-30%, and once it runs smoothly, gradually increase the proportion. Give the workshop and molds a period to adapt; this is much safer than mixing in full from the beginning.

(Note: This section is a synthetic case for demonstrating the selection concept, and all character and company names do not correspond to real entities.)

Decide whether to do injection molding or foaming first, and the positions of the materials will naturally become clear.

Before selecting materials, save the table below on your phone and just match the items when needed. One more reminder before using it: no matter which grade you choose, remember to ask the supplier for three things—the batch data from the manufacturer, the notched impact strength, and a statement on color consistency. If you have all three, the yield of recycled HIPS won’t have major issues.

Application scenario	Recommendation Level	Precautions	When not to use
White appliance panel/back panel	High-impact grade recycled HIPS	Mix new material proportionally and monitor impact color differences.	Made entirely from recycled materials for high-appearance exposed parts
Stationery casing/toys	General-purpose injection molding grade recycled HIPS	MFR needs to be stable, the color can be slightly adjusted	Using mixed-color material to make light-colored appearance parts
Appliance Liner / Blister Sheet	Natural Light Gray Recycled HIPS	Uniform color, free of impurities	Material with many impurities is used for blister molding
Electrical components	Black flame-retardant recycled HIPS	Flame retardant and impact resistance both meet standards	Non-flame-retardant materials used for parts with flame-retardant requirements
Transparent stationery/photo frame	Recycled GPPS Transparent White Material	Few impurities, good light transmission	Mixed-color recycled material used for transparent parts
Foam packaging / cushioning	Foam-grade recycled PS	Walk the foaming line alone	Take the plastic for foaming

Recycled HIPS, a cost-effective choice for appliance liners and stationery casings

Disclaimer: The brands and trademarks mentioned in this article are owned by their respective manufacturers. This article is a third-party material selection knowledge sharing, and the specific grades, parameters, prices, certifications, and other information mentioned are subject to the latest official data from the manufacturers. This article does not constitute any purchasing or investment advice.