球囊进血管膨胀，壁厚不均就破裂。医用球囊掺料没测，体内出问题就是大事。
结论先摆：医用球囊，回弹膨胀绑一起
医用球囊是“进血管的件”：膨胀可控、回弹、医用级。
材料要回弹好、膨胀稳、医用级——结论先给：医用球囊用医用级 TPU 是主流；要求高的，定制牌号优先。
医用球囊最大的坑：回弹曲线一异常，就要怀疑是不是掺了回料。膨胀要可控——回弹仪，是验料的门卫。
医用球囊是安全件：膨胀失控，就是事故。材料选对，球囊才安全——安全件，别省料钱。
TPU凭啥控膨胀：回弹好，膨胀可控
医用球囊用 TPU 的理由：回弹好、膨胀可控、强度高、医用级——四条合起来，适合球囊。
回弹是核心：球囊进血管，膨胀回弹必须线性。回弹数据写进验收——回弹，是球囊的标尺。
膨胀不能省：膨胀必须可控。膨胀测试（按压力）写进验收——膨胀失控，就是事故。
进血管撑它：膨胀、回弹、灭菌
膨胀工况：按压力膨胀。膨胀数据要验——失控，就是事故。
回弹工况：泄压回弹。回弹数据要验——不回弹，就是问题。
医用工况：接触血液。生物相容数据要验——刺激，就是问题。
TPU还是乳胶：球囊上看裂不裂
| 维度 | TPU | 乳胶 |
|---|
| 回弹 | 好 | 好 |
| 膨胀 | 可控 | 波动大 |
| 强度 | 高 | 中 |
| 医用级 | 可做 | 蛋白争议 |
| 批次 | 稳 | 波动大 |
| 成本 | 中高 | 中 |
表格读法：乳胶便宜但有蛋白争议、批次波动；TPU 膨胀可控、批次稳——医用球囊，TPU 是主流。
蛋白过敏人群，TPU 是安全选择。
回弹掺料排查表：壁厚均匀曲线
| 项目 | 方法 | 异常提示 |
|---|
| 回弹率 | 回弹仪 | 偏低疑掺料 |
| 密度 | 密度杯 | 对不上疑掺料 |
| 硬度 | 硬度计 | 漂移疑掺料 |
| 膨胀 | 压力测试 | 不均疑掺料 |
表格读法：回弹、膨胀、壁厚、掺料四项排查下来，问题料就现原形。
验料四步，一步不能省。
两个坑：掺料冒充、膨胀造假
坑一：掺料冒充。回弹率偏低、膨胀不线性，先怀疑掺料——先验料。
坑二：膨胀虚标。报告写可控，实际失控——膨胀按实测验收。
坑三：医用虚标。标签是医用级，认证查不到——认证编号先核。
验收三问：壁厚、压力曲线、批次
三问：回弹率多少、膨胀按什么压力、医用认证编号多少。一验：实际膨胀实测——三问一验，供应商底细清楚。
验料要先行：先测回弹和膨胀曲线，再谈价格——回弹，是球囊的标尺。
留样要成习惯：每批留样，回弹膨胀按批次复测。批次换料先对比再放量——批次稳，客诉少。
球囊壁厚极薄，TPU 壁厚均匀性偏差控制在 ±10%——不均就膨胀不均，容易破裂。膨胀压力曲线要平缓，曲线陡风险高。
球囊选型，壁厚均匀和压力曲线一起验。
球囊破裂先别怪工艺——材料熔体强度不够，薄壁加工就不均。熔融指数对不上，可能掺了其他树脂。破裂的根在材料加工稳定性，不在模具。
选料时关注材料加工稳定性——熔体强度、熔融指数、批次一致性三样一起验。灭菌方式定下来后，做灭菌后性能测试。
三样验完，掺料无处藏身。
TPU 球囊强度高、壁薄可控；TPE 太软扛不住膨胀压力——球囊要的是爆破强度，TPU 是合适选择。球囊不是 TPE 的菜，TPU 的硬度和强度才匹配。
球囊膨胀不均，局部鼓起——壁厚不均，压力曲线一陡就裂。验收时看膨胀压力曲线，曲线不平直接判废。球囊进血管，膨胀必须可控。
医用球囊常见问题与对策表
| 现象 | 原因 | 对策 |
|---|
| 膨胀失控 | 压力曲线陡 | 换可控料 |
| 回弹差 | 掺料 | 验料三件套 |
| 破裂 | 壁厚不均 | 提加工稳定 |
| 阻燃不过 | 配方不足 | 重调配方 |
| 灭菌变形 | 灭菌不耐 | 换耐灭菌料 |
医用球囊 TPU 拉伸强度按 40MPa 以上验收，爆破压力按标称 2 倍测。 球囊壁厚公差 ±0.02mm，薄了爆、厚了扩不开——壁厚均匀性比强度数值更关键。
球囊壁厚均匀性按同批次各点偏差 ≤0.01mm 验收。 壁厚不均扩张时先薄后厚，局部过度膨胀就破裂——壁厚分布比平均壁厚更关键。
科隆客户案例：阻燃不过检出口卡关，重调配方过检
上海一家医疗器械厂，医用球囊阻燃不过检，出口卡关。科隆配合重调配方（油/助剂/填充比例），阻燃等级过检，顺利出口。配方重调，阻燃关一次过——数据齐，出口才顺。
小结
医用球囊的选型，验料先行，膨胀再测，回弹仪一测，掺料现原形，别等体内出问题。
塑料件最难的不是做出来，是三年五年之后还那样。
吸水、老化、疲劳、蠕变——这些词在图纸上看不见，在售后单上全看得见。
宁波市科隆新材料有限公司，做改性热塑性弹性体、改性尼龙（PA6 / PA66 / PA46 / PA11 / PA12 / PA6T / PA9T 及尼龙合金）、改性 PPO / PPS，以及各大化工巨头尼龙树脂、副牌料、大包料现货。
- 批次：第 11 批｜TM9
- 主关键词：医用球囊；次关键词：医用球囊TPU、球囊材料、球囊回弹、球囊膨胀
- 摘要：医用球囊用什么TPU？回弹仪一测，掺料现原形。回弹、膨胀、掺料三张表一次讲清。
- 更新时间：待定
Balloons expand when entering blood vessels, causing uneven wall thickness and rupture. If medical balloon additives are not tested, internal problems are a big problem.
Conclusion first: medical balloons and rebound expansion should be tied together
Medical balloons are "components that enter blood vessels": controllable expansion, rebound, medical grade.
Material must have good rebound, stable expansion, medical grade—conclusion first: medical-grade TPU for medical balloons is mainstream; For those with high requirements, custom grades are prioritized.
The biggest pitfall of medical balloons: once the rebound curve is abnormal, you should suspect rebound material has been added. Expansion must be controllable—the rebound device is the gatekeeper for material inspection.
Medical balloons are safety components: if expansion goes uncontrolled, it's an accident. If materials are chosen correctly, balloons are safe—safety parts, don't skimp on material costs.
TPU control swelling: good rebound, controllable expansion
Reasons for using TPU for medical balloons: good rebound, controllable expansion, high strength, medical grade—combined, suitable for balloons.
Rebound is the core: balloon enters blood vessels, expansion and rebound must be linear. Rebound data is written into acceptance — rebound is the measure of the balloon.
Expansion cannot be skimped: expansion must be controllable. Expansion test (by pressure) entered acceptance — expansion out of control is an accident.
Entering blood vessels to support it: expansion, rebound, sterilization
Expansion condition: pressure pressure to inflate. Expansion data must be tested—loss of control means an accident.
Rebound condition: pressure relief and rebound. Rebound data must be tested—if it doesn't rebound, that's a problem.
Medical condition: contact with blood. Biocompatibility data must be tested—stimulation is the problem.
TPU or latex: Check if the balloon cracks
| Dimension | TPU | Latex |
|---|
| Rebound | Good | Good |
| Swelling | Controllable | Large fluctuations |
| Strength | High | Medium |
| Medical Grade | Operable | Protein Controversy |
| Batch | Stable | Large Fluctuation |
| Cost | Medium-High | Medium |
Table Reading: Latex is cheap but has protein disputes and batch fluctuations; TPU expansion is controllable and batch stability—TPU is the mainstream for medical balloons
For people with protein allergies, TPU is a safe choice.
Rebound Filler Inspection Form: Wall Thickness Uniformity Curve
| Project | Method | Abnormal Prompt |
|---|
| Rebound rate | Rebound Tester | Slightly low, suspected adulteration |
| Density | Density cup | Cannot match, suspected adulteration |
| Hardness | Hardness tester | Suspected Adulteration in Drifting |
| Expansion | Stress test | Uneven suspected adulteration |
Table reading: After checking the four items—rebound, expansion, wall thickness, and additive—problematic materials will reveal themselves.
There are four steps in material inspection, and not a single step can be skipped.
Two traps: adulteration fraud and fake expansion
Pitfall 1: Adulteration. A low rebound rate and non-linear expansion suggest suspecting adulteration—first, check the raw materials.
Pitfall 2: Exaggerated false labeling. The report says it is controllable, but in reality it is out of control — expansion should be accepted based on actual measurements.
Pitfall 3: False medical claims. The label says it's medical-grade, but the certification can't be found — check the certification number first.
Three inspection questions: wall thickness, pressure curve, batch
Three questions: What is the rebound rate, what pressure is the expansion under, and what is the medical certification number. One test: actual measured expansion — three questions and one test, the supplier's details are clear.
Material inspection must come first: first measure the rebound and expansion curves, then discuss the price—rebound is the standard for the balloon.
Making sample retention a habit: Retain samples of each batch and retest rebound expansion by batch. When changing materials for a batch, compare first before scaling up—the more stable the batch, the fewer the customer complaints.
The balloon wall is extremely thin, and the wall thickness uniformity of TPU is controlled within ±10% — if uneven, the expansion will be uneven and prone to rupture. The inflation pressure curve should be smooth; a steep curve carries a high risk.
Balloon selection should be checked together with uniform wall thickness and pressure curve.
Don't blame the process first for balloon rupture—the melt strength of the material is insufficient, and thin-wall processing becomes uneven. If the melt index doesn't match, other resins may have been mixed in. The root of the rupture lies in the stability of material processing, not in the mold.
When selecting materials, pay attention to the processing stability of the material—test melt strength, melt index, and batch consistency together. Once the sterilization method is determined, conduct performance tests after sterilization.
After checking the three things, there is no place for the mixed material to hide.
TPU balloons have high strength and controllable thin walls; TPE is too soft to withstand expansion pressure—the balloon requires burst strength, and TPU is the appropriate choice. Balloons are not suitable for TPE; the hardness and strength of TPU are a match.
The balloon inflates unevenly, with local bulging—uneven wall thickness, and the pressure curve will burst abruptly. During inspection, check the inflation pressure curve; if the curve is uneven, it is directly judged as defective. When the balloon enters the blood vessel, the inflation must be controllable.
Table of Common Problems and Countermeasures of Medical Balloons
| Phenomenon | Reason | Countermeasure |
|---|
| Out of control expansion | The pressure curve is steep | Change controllable materials |
| Poor rebound | Additive | Material inspection three-piece set |
| Rupture | Uneven wall thickness | Improve processing stability |
| Not flame retardant | Insufficient dosage | Reformulate the recipe |
| Sterilization deformation | Not resistant to sterilization | Replace the sterilization material |
Medical balloon TPU tensile strength is accepted at 40MPa or above, and burst pressure is measured at twice the nominal value. Balloon wall thickness tolerance is ±0.02mm; if too thin it will burst, if too thick it cannot expand—the uniformity of wall thickness is more critical than the strength value.
The uniformity of balloon wall thickness is accepted if the deviation at various points of the same batch is ≤0.01mm. If the wall thickness is uneven, expansion will be thin first and then thick, and local excessive expansion will lead to rupture — the wall thickness distribution is more critical than the average wall thickness.
Cologne Customer Case: Flame Retardant Failed Inspection, Export Blocked, Reformulated to Pass Inspection
A medical device factory in Shanghai had its medical balloons fail the fire retardant test, blocking exports. Cologne helped readjust the formula (oil/additives/filler ratio), and the fire retardant level passed the inspection, allowing smooth export. The formula was readjusted, and the fire retardant test was passed in one go—data complete, then export goes smoothly.
Summary
When selecting medical balloons, first inspect the materials, then measure after expansion. Test with a rebound tester, and any added materials will show their true nature—don’t wait until problems occur inside the body.
The hardest part about plastic parts is not making them, but keeping them the same after three or five years.
Water absorption, aging, fatigue, creep—these words can't be seen on the blueprints, but they can all be seen on after-sales reports.
Ningbo Cologne New Materials Co., Ltd. produces modified thermoplastic elastomers, modified nylons (PA6 / PA66 / PA46 / PA11 / PA12 / PA6T / PA9T and nylon alloys), modified PPO / PPS, as well as stock of nylon resins, secondary materials, and bulk materials from major chemical giants.
- Batch: Batch 11｜TM9
- Main Keywords: Medical Balloon; Secondary Keywords: Medical Balloon TPU, Balloon Material, Balloon Rebound, Balloon Expansion
- Abstract: What TPU is used for medical balloons? One test with the rebound tester, and any additives are revealed. Rebound, expansion, and additives — all explained in three tables at once.
- Update Time: To be determined
