急停转身鞋钉断了，场上崴脚赔到怕。足球鞋鞋钉强度没选对，安全就是赌。
鞋钉断在急停那一下
足球鞋鞋钉是“抓草转向的件”：耐磨、抓地、强度。材料要耐磨、抓地、强度高——结论先给：足球鞋鞋钉用 TPU 是主流；童鞋鞋钉，软底加耐磨兼顾。
足球鞋鞋钉最大的坑：童鞋软底，耐磨也要跟上。软底舒适，但耐磨不能松——安全，别打折。
足球鞋鞋钉是功能件：磨平、打滑都是问题。材料选对，鞋子才稳——功能件，别省料钱。
鞋钉为什么非 TPU 不可
足球鞋鞋钉用 TPU 的理由：耐磨好、强度高、抓地可做、效率高——四条合起来，适合鞋钉。
耐磨是核心：草地摩擦。耐磨测试写进验收——磨平，就是问题。
强度不能省：急停转向。强度测试写进验收——断钉，就是问题。
抓草急停安全，三道关
抓草工况：草地抓地。抓地数据要验——打滑，就是问题。
急停工况：急停转向。强度数据要验——断钉，就是问题。
安全工况：童鞋使用。软硬数据要验——过硬，就是问题。
TPU 还是 TPR？鞋钉一表看清
| 维度 | TPU | TPR |
|---|
| 耐磨 | 强 | 中 |
| 强度 | 高 | 中 |
| 抓地 | 好 | 中 |
| 成本 | 高 | 中 |
| 硬度 | 可调 | 可调 |
| 用途 | 专业 | 入门 |
表格读法：TPU 耐磨强度好但贵；TPR 性价比高——专业鞋钉 TPU，入门 TPR。
按级别选：专业 TPU，入门 TPR。
鞋钉验收：强度安全两笔账
| 项目 | 方法 | 标准 |
|---|
| 耐磨 | 磨耗测试 | 按标准 |
| 强度 | 弯折测试 | 按力值 |
| 抓地 | 摩擦测试 | 按草面 |
| 硬度 | 硬度计 | 按适用 |
表格读法：耐磨、抓地、弯折四项走完，鞋钉才敢上脚。
安全，别打折。
只图软底，三个坑崴脚赔
坑一：只图软底。软过头磨两周就平，操场抓地全丢——耐磨必测。
坑二：强度漏测。断钉——强度测试，必测。
坑三：抓地漏测。打滑——抓地测试，必测。
选鞋钉料先问这三点
三问：耐磨按什么标准、强度按多少力、硬度多少。一验：实际踢球实测——三问一验，供应商底细清楚。
安全验证要先行：先测耐磨和抓地，再谈价格——安全，别打折。
留样要成习惯：每批留样，耐磨强度按批次复测。批次换料先对比再放量——批次稳，客诉少。
TPU 鞋钉硬度 Shore A 85-95，软底童鞋也要守在这个区间。 硬度过高硌脚、过低磨平快，童鞋护踝和耐磨要一起兜。
TPR 性价比高但耐磨中等，TPU 耐磨强但贵。 入门训练鞋 TPR 够用，比赛抓地 TPU——按场地级别选，别一上来就上 TPU。
鞋钉断钉不是强度差，是急停转向力值没测。 按实际场地做弯折加扭转，别只报拉伸强度——断钉出在工况，不在数据表。
鞋钉验收三件套：磨耗、急停扭转、拆装螺纹。 天然草人造草泥地分别测，可拆卸钉反复拆装 500 次核螺纹强度。
90A 定锚加扭转力值过检，鞋钉磨平和断钉投诉双双下降。 每批留样测耐磨加强度，场地数据按场记录归档。
足球鞋鞋钉常见问题与对策表
| 现象 | 原因 | 对策 |
|---|
| 磨平 | 耐磨不足 | 换耐磨料 |
| 断钉 | 强度不足 | 换高强度料 |
| 打滑 | 抓地不足 | 改钉形 |
| 成本超标 | 牌号选宽 | 按工况选 |
| 批次漂移 | 配方波动 | 锁窗口 |
足球鞋钉拉伸强度按 35MPa 以上验收，扭转力值按急停实测。 鞋钉断钉出在急停转向，不在静态拉伸——按真实场地做扭转测试，别只报拉伸强度。
可拆卸钉螺纹配合按反复拆装 500 次不滑牙验收。 螺纹处 TPU 料收缩小，PP 基料螺纹易滑——可拆卸钉选低收缩 TPU，别用通用 TPR。
鞋钉抓地按天然草人造草分别测，抓地力值差两倍。 同一款钉在不同场地抓地力天差地别——按目标场地做抓地测试，
别拿一种场地数据报所有。
足球鞋鞋钉按场地类型选长度，天然草长钉人造草短钉。 同一款鞋钉换场地抓地力差一倍——按目标场地换钉，别一双钉打所有场。
科隆客户案例：成本超标报价无竞争力，定制牌号回预算
青岛一家鞋材厂，足球鞋鞋钉材料成本超标，报价没竞争力。科隆配合定制耐油/耐温专用牌号，性能达标，成本回到预算线内。按工况定制，成本才压得下来——成本超标，先看牌号选宽了没有。
小结
足球鞋鞋钉的选型，耐磨先测，安全再核，童鞋软底耐磨也要跟上，安全别打折。
总有人问：副牌料到底能不能用。
我们的回答一直没变——能用的地方很多，不能用的地方一处都不能碰。它和回料是两回事：一个是指标偏了，一个是分子链断了。
宁波市科隆新材料有限公司，主营改性热塑性弹性体、改性尼龙（PA6 / PA66 / PA46 / PA11 / PA12 / PA6T / PA9T 及尼龙合金）、改性 PPO / PPS；各大化工巨头的尼龙树脂、副牌料、大包料现货。
- 批次：第 12 批｜TS8
- 主关键词：足球鞋鞋钉；次关键词：足球鞋鞋钉TPU、鞋钉耐磨、鞋钉抓地、鞋钉安全
- 摘要：足球鞋鞋钉用什么TPU？童鞋软底，耐磨也要跟上。耐磨、抓地、安全三张表一次讲清。
- 更新时间：待定
Sudden stops and turns cause cleats to break, and sprained ankles on the field are terrifying. If the cleat strength of soccer shoes is not chosen correctly, safety becomes a gamble.
The cleat broke during that sudden stop
Football boot studs are the 'components for gripping grass and changing direction': wear-resistant, ground-gripping, and strong. The materials need to be wear-resistant, ground-gripping, and high-strength — conclusion first: TPU is mainstream for football boot studs; for children's shoes, the studs should have a soft base combined with wear resistance.
The biggest pitfall of football shoe studs: children's shoes have soft soles, and wear resistance must also keep up. Soft soles are comfortable, but wear resistance cannot be compromised—safety should not be discounted.
Football cleats are functional components: if they wear down or slip, it's a problem. Choosing the right material keeps the shoes stable—functional components, don't skimp on material costs.
Why must the shoe studs be TPU?
Reasons for using TPU for football boot studs: wear-resistant, high strength, good traction, and high efficiency—combined, these four qualities make it suitable for studs.
Wear resistance is key: grass friction. Wear resistance testing is written into the acceptance—wearing down is the problem.
Intensity cannot be reduced: emergency stop steering. Intensity tests must be included in the acceptance—broken nails indicate a problem.
Emergency stop when grabbing grass is safe, three checkpoints
Grass gripping condition: gripping the ground on grass. Gripping data needs to be checked—slipping is a problem.
Emergency stop situation: Emergency stop steering. The strength data needs to be checked—broken bolts, that's the problem.
Safe condition: For children's shoes. The softness and hardness data must be checked—if it's too hard, it's a problem.
TPU or TPR? Check the shoe studs at a glance
| Dimension | TPU | TPR |
|---|
| Wear-resistant | Strong | middle |
| Intensity | Tall | middle |
| grip | Good | middle |
| Cost | Tall | middle |
| Hardness | Adjustable | Adjustable |
| Purpose | Professional | Introduction |
Table reading: TPU has good wear resistance but is expensive; TPR has high cost performance — professional shoe studs use TPU, beginners use TPR.
Choose by level: professional TPU, entry-level TPR.
Shoe Nail Inspection: Two Accounts of Strength and Safety
| Project | Method | standard |
|---|
| Wear-resistant | Wear test | According to the standard |
| Intensity | Bend test | By force value |
| grip | Friction Test | On the grass |
| Hardness | Hardness tester | As applicable |
How to read the table: Only after completing the four items of wear resistance, grip, bending, can the shoe studs be used.
Safety, no compromise.
Only care about soft soles, three holes and you'll sprain your ankle and pay for it
Pitfall 1: Focusing only on a soft sole. If it's too soft, it will flatten after two weeks of wear, losing all grip on the playground — durability must be tested.
Pitfall 2: Missed strength testing. Broken screws—strength testing is a must.
Pitfall three: Testing by grabbing the floor drain. Slippage—floor grip test, must test.
Ask these three points first when choosing shoe studs
Three questions: What is the standard for wear resistance, how much force for strength, and what is the hardness? One test: actual test by kicking the ball — three questions and one test, understanding the supplier's details clearly.
Safety verification comes first: test wear resistance and grip before discussing price—safety should not be discounted.
Making sample retention a habit: retain samples from each batch, and re-test the abrasion strength by batch. When changing materials for a batch, compare first before scaling up — stable batches lead to fewer customer complaints.
The hardness of TPU shoe studs is Shore A 85-95, and soft-soled children's shoes should also stay within this range. If the hardness is too high, it will hurt the feet; if it is too low, it will wear down quickly. Children's shoes need to ensure both ankle support and wear resistance.
TPR is cost-effective but has moderate wear resistance, while TPU is highly wear-resistant but expensive. For beginner training shoes, TPR is sufficient; for competition traction, choose TPU — select according to the level of the court, and don’t go for TPU right away.
Broken shoe studs are not due to poor strength, but because the force values for sudden stops and turns were not measured. Perform bending and torsion tests according to the actual field conditions, and don’t just report tensile strength—the studs break due to working conditions, not from the datasheet.
Three-piece set for cleat inspection: wear, emergency stop torsion, and screw assembly/disassembly. Tests are performed separately on natural grass, artificial turf, and clay; removable studs are repeatedly assembled and disassembled 500 times to check screw strength.
The 90A fixed-anchor with torsion force value passed inspection, and complaints about worn-down and broken spikes both decreased. Samples from each batch are kept for wear resistance testing, and field data are recorded and archived according to site logs.
Common Problems and Solutions of Soccer Shoe Studs
| Phenomenon | Reason | Countermeasure |
|---|
| grind smooth | Insufficient wear resistance | Replace wear-resistant material |
| Broken nail | Insufficient strength | Switch to high-strength material |
| slip | Insufficient traction | Change to nail shape |
| Cost overrun | Select Grade Width | Select according to operating conditions |
| Batch Drift | Formula fluctuation | Lock window |
The tensile strength of soccer shoe studs should be accepted at above 35MPa, and the torsion force value should be measured during sudden stops. Stud breakage occurs during sudden stop turns, not in static stretching—torsion tests should be conducted on real fields, not just report tensile strength.
The removable pin threads must pass the inspection of not stripping after being repeatedly assembled and disassembled 500 times. The TPU material shrinks less at the threads, while the PP base material threads are prone to slipping — choose low-shrinkage TPU for removable pins, and do not use general TPR.
The traction of shoe studs is measured separately on natural grass and artificial turf, and the traction value differs by a factor of two. For the same type of stud, traction varies greatly on different surfaces — test the studs for the target surface.
Do not use data from one type of surface to represent all.
Choose the length of football shoe studs according to the type of surface: long studs for natural grass, short studs for artificial turf. The same studs on different fields can have a twofold difference in traction — change studs according to the target field, don’t use one pair for all.
Cologne Customer Case: Cost Overrun Led to Uncompetitive Quote; Custom Grade Returned Costs to Budget
A shoe material factory in Qingdao had football shoe stud material costs exceeding budget, resulting in an uncompetitive quote. Cologne assisted with custom oil/heat-resistant grades that met performance standards and brought costs back within the budget. Customization according to working conditions is necessary to control costs — if costs exceed, the first step is to check if the grade selection was too broad.
Summary
When selecting football shoe studs, first check wear resistance, then verify safety. Children’s soft soles must also follow wear resistance standards, and safety should not be compromised.
There are always questions: Can secondary grade materials be used?
Our answer has always been the same — they can be used in many areas, but not at all in places where they shouldn’t. It’s different from recycled material: one is due to shifted specifications, the other is broken molecular chains.
Ningbo Cologne New Materials Co., Ltd., specializes in modified thermoplastic elastomers, modified nylons (PA6 / PA66 / PA46 / PA11 / PA12 / PA6T / PA9T and nylon alloys), modified PPO / PPS; offers stock of major chemical companies’ nylon resins, secondary grades, and bulk material.
- Batch: 12th Batch｜TS8
- Main Keyword: Football Shoe Studs; Secondary Keywords: Football Shoe Stud TPU, Stud Wear Resistance, Stud Traction, Stud Safety
- Abstract: What TPU should be used for football shoe studs? Children’s soft soles must also follow wear resistance. Wear resistance, traction, and safety are explained in three tables.
- Update Time: TBD
